The issue about electric bike battery for bike kit

We purchased a electric bike kit including motor controller, hub motor wheel, throttle, brake lever and with 36V 12AH Lithium Ion electric bike battery that used for testing 36V solar charger from one supplier, not from leaf motor. After charging this electric bike battery for 10 hours by better solar power, full charged, we rode the bike, but hub motor wheel only run about 8km. Then we use 110-230Ac charger to charge this electric bike battery and full charged it. After test, we found this hub motor wheel is still lasted for around 8km.
We use a amperemeter in series to electric bike kit system, powered on and rode it. We got the current is about 5A. The RPM is 257RM.We use 26” hub motor wheel.
We calculate the speed is about 32Km/per hour.
See below formula:
（3.14×26”×0.0254）× 257RPM × 60 minutes ÷ 1000 (m-Km)=32km
If this is 12Ah battery, per hour lost 8ah.We can use 1.5 hours.
See below formula:
12Ah ÷ 8ah/per hour= 1.5hours
We think full charge this electric bike battery per time, the hub motor wheel can run about max 48 km. 32km/per hour × 1.5 hours = 48 km
There is definitely a problem with this electric bike battery, I’m not sure whether electric bike kit is because of the solar charging or our testing, or if it has a fault. But I need a replacement electric bike battery asap, because we don’t have any more 36v electric bike battery, and we sold 1 set of electric bike kit with li battery last week. I think BMS inside this electric bike battery no problem. The problem comes from the li battery cells. Maybe this electric bike battery had stayed in warehouse for a long time and haven’t charged it. It will make the electric bike battery cut down the achieve distances and use life.
So if solve this problem and let my hub motor to work asap, only replace all cells or replace new electric bike battery.
We are angry with our supplier, sent them many emails and no any reply.
Thank you, leaf motor. Help us found the electric bike battery ‘s problem. We are going to order leaf’s products in near future.
Hub motor, electric bike battery, electric bike kit supplier: Leaf Motor Technology Co.,Ltd
Website:https://www.leafmotor.com

make a 48V hub motor electric bike kit work at 36V

I have recently bought a DIY electric bike kit  from you, where I have bought a 36V battery and a 48V hub motor & brushless motor controller. I thought that when I ordered from your online internet shop, you would check, that the electric bike kit system would work..

On the homepage you write, that I can force the 48V hub motor controller to work with lower voltages.Also, the 48V thumb hub motor controller does not work. The twist controller works.
I have called your office and found out, that the problem is, that the 48V hub motor controller cuts off the electric bike kit system to protect the li battery. And the only solution is to manually override the system, but that is not an ideal way to operate the e-bike.

I have now ordered a new hub motor controller and thumb throttle for 36V from your homepage. What I would like you to do, is to write on the package you send me, that the package you send me is a guarantee replacement.

I do not wish to discuss guarantee and other issues with you, it is much easier for me to order new parts, but I would like to avoid to have to pay customs and VAT again for the same things. Also it takes weeks before the goods get through customs.

I also have one more suggestion for improvement:Please put 2*2 nuts on the electric bike motor wheel to be able to secure them, because my front 48V 1000w electric bike motor wheel fell off while I was starting with the e-bike. (while driven by 36V, ½ power – where I pull the break lever, push the cruise control 5 times, and use the cruise control to operate the electric bike motor) Also it would be nice if you could specify how hard I should tighten the nuts on the electric bike motor wheel.

20Nm? 60Nm?, I would like to tighten them well, but I do not wish to brake the thread. My transaction ID of electric bike kit order is 3FA78294KK410865B

Hub motor,electric bike motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd
Website:https://www.leafmotor.com

issue about electric bike kit battery

We purchased an electric bike kit including motor controller, hub motor wheel, throttle, brake lever and with 36V 10AH bottle style Lithium Ion electric bike battery that used for testing 36V solar charger from one supplier, not from leaf motor. After charging this electric bike battery for 10 hours by better solar power, full charged, we rode the bike, but hub motor wheel only run about 8km. Then we use 110-230Ac charger to charge this electric bike battery and full charged it. After test, we found this hub motor wheel is still lasted for around 8km. We use a ampere meter in series to electric bike kit system, powered on and rode it. We got the current is about 5A. The RPM is 257RM.We use 26” hub motor wheel. We calculate the speed is about 32Km/per hour. See below formula: （3.14×26”×0.0254）× 257RPM × 60 minutes ÷ 1000 (m-Km)=32km If this is 10Ah battery, per hour lost 8ah.We can use 1.25 hours. See below formula: 10Ah ÷ 8ah/per hour= 1.25hours We think full charge this electric bike battery per time, the hub motor wheel can run about max 40 km. 32km/per hour × 1.25 hours = 40 km There is definitely a problem with this electric bike battery, I’m not sure whether electric bike kit is because of the solar charging or our testing, or if it has a fault. But I need a replacement electric bike battery asap, because we don’t have any more 36v electric bike battery, and we sold 1 set of electric bike kit with li battery last week. I think BMS inside this electric bike battery no problem. The problem comes from the li battery cells. Maybe this electric bike battery had stayed in warehouse for a long time and haven’t charged it. It will make the electric bike battery cut down the achieve distances and use life. So if solve this problem and let my hub motor to work asap, only replace all cells or replace new electric bike battery. We are angry with our supplier, sent them many emails and no any reply. Thank you, leaf motor. Help us found the electric bike battery ‘s problem. We are going to order leaf’s products in near future. Hub motor, electric bike battery, electric bike kit supplier: Leaf Motor Technology Co., Ltd Website:https://www.leafmotor.com/

How to build spokes on hub motor for electric bike ?

DIY electric bike conversion kit and convert your bike is funny. Sometimes we prefer to purchase spoke hub motor , bike rim and spokes. And build spokes on electric bike motor by ourselves.
If we want to convert 26inch front wheel, we should purchase 1 set of front spokes hub motor, 26inch rim and 36pcs of spokes. We can purchase them from leaf bike motor shop online.
Received goods and check them:
1. How many spokes you received. Generally we need 36 pcs spokes to built on hub motor and 12 gauge spokes for electric bike. 13, 14 gauge spokes are too thin, just for common bike.
2. There are 36 eyelet on bike rim and hub motor.
3. Check nipple and the dia. of eyelet on rim, make sure the nipple can put into eyelet.
Calculate the length of spoke :
If you use 205 leaf front hub motor, the eyelet to eyelet of rim is 511mm that is 26inch rim, spokes should be 155mm length.
You need below tools to install spokes on hub motor.
1.iron shelf
2.slotted screwdriver
3.nipple wrench
4.magnet
5.rubber hammer
6.tape measure
7.calipers
Done check, everything is okay. But we found the dia. of nipple is 4.5mm and the rim is also 4.5mm. These eyelets are too small. See pictures.
Get an electric drill and 4.8mm aiguille. Drill 36 pcs of eyelets on bike rim first. Adjust the iron shelf so that the dia. is 100mm. Because standard front fork is 100mm. Then put the rim inside the iron shelf, hold on the hub motor. Make the first spoke wear into hub from left side, the next from right side. One by one from left side to right side. Done install all 36 pcs of spokes, please check them whether correct. See pictures.
If no problem, we should hold spokes on rim by nipples First hold one spoke on left side, then cross to fix another spoke on left side. Next step, cross two spokes on rights side and fix them. Left side, right side, a group of four spokes. See pictures.
Fix all spokes, we should use wrench to tight spokes a little, please don’t be too tight. Use hand to turn wheel, make sure there is no noise from friction of rim and nipple. Use rubber hammer to knock rim when the wheel is running so that the rim will be not jumping up and down. Still to tight spokes a little. See pictures.
Turn wheel, you will find the rim from left side to right side. In order to make the wheel running in the middle. We use calipers to measure and get the data. Then use a magnet to hold a pin. See pictures. If rim to the left, we tight right side spokes or loose left side spokes. See pictures.
It takes about 1 hour to build an wheel.

Hub motor was very sluggish

Question:While trying to get the hub motor up and running here we have run in to some problems. After installing the hub motor wheel in the fork it was very sluggish to turn and took quite a bit of effort, not freewheeling at all. The first time we plugged the battery (fully charged 48V 12AH LiFePo4 at 52.9V) in to hub motor (without the throttle connected to the controller cable) the hub motor beeped three times. When we hooked up the controller cable black and yellow pin connectors to the corresponding ones on the throttle there was no response from the electric bike motor , but the battery level lights did light up. We tried both throttles sent with the same results.
As it was the weekend I went to the forum and looked there for assistance. I received some good feedback that the 3 beeps we heard were a signal that the throttle was not functionable which is what we found as soon as we hooked up the throttle. We have checked all the leads for correct amperage as per his instructions with positive results.
I am assuming that electric bike kit is bench tested before it leave there? The packaging was undamaged upon delivery and all seemed in good order upon receipt. If you could please advise us on what to do to get this resolved we would appreciate it as we want to get on with our trials here to be able to get out product to market by summer.
I have checked my throttle and hub motor controller wires against your PDF diagram and there seems to be some discrepancy? I wish my camera was working but I will describe my findings. Diagram Throttle Black 3 pin shows: Red? perhaps Orange?/White/Blue Our Throttle Black 3 pin has:
Orange/White/Black from core with black jump to yellow 2 pin Diagram Controller Black 3 pin has: Red? perhaps Orange?/black/Yellow Hub Motor Controller Black 3 pin has: Rust from Core with Red Jumper to PAS White three pin/White/Black from core with Black jumper to yellow 2 pin
I checked the 8 pin connector again and can’t see that it isn’t making good contact. No bent pins or obstructions.Electric Bike Motor still beeps three times upon connecting to full battery as described with and without full connections of cables.
Yes jumping the two holes as indicated does make the electric bike kit run. It seemed like at first that by moving the controller wire that the electric bike motor would stop and start as if there was a short right at the junction and we thought that might be the problem. We hooked up the cable but I still am not getting any response from either throttle when hooked up to the black two pin connector even if I move the cable at the junction and now using the jumper the short method that issues seems to have gone away?
We are trying hard to make this electric bike kit work here but I have to admit we are getting a bit frustrated. The throttle cable while hooked up shows 5.0 amps on the red wire and from .8 amps at rest and 3.8 amps on the white wire when at full throttle like it should? Without the black pin connector together there are 5.0 amps at the red wire and .1 amps at the white wire if that is any useful information.
Hub motor,electric bike motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd
Source:https://www.leafmotor.com

The issue about 250W hub motor electric bike kit

Bought 1 set of electric bike kit from one supplier in China two months ago. Sent more than 10 emails, haven’t gotten any reply. I met below issue, hope solve it.

When I was riding my electric bike three weeks ago, the 250w mini front hub motor suddenly started to make a strange and strong noise. If I try to turn the twist throttle on when the e-bike doesn’t have any load, I keep the hub motor wheel in the air. The electric bike motor works fine and electric bike kit does not make any noise.

However, if I try riding my electric bike and turning the throttle on, the electric bike motor starts making a strong and continuous noise. I tried to riding my bike keeping the brakes continuously pressed and any noise appears so it seems to be some electric problem. It is very strange and I am so much worried.

I took off electric bike kit wheel and used screwdriver to disconnect six screw nuts, took apart hub motor cover and found there was a rotor-winding, two bearings, three sets of 42-gear, 1 set of 21-gear on the axis, 1 set of 81-gear on the hub. There wasn’t any impurity inside the hub motor. Re-install and test electric bike motor wheel, still have the same problem. Don’t know what’s the problem.

Contact my supplier many times and can’t get any reply. I looked for answers by google, yahoo and bike forums, still can’t find the correct answer. Yesterday I got a message from my US friend about there was a company, leaf motor can help me. So I sent an email to leaf motor.

Surprisingly just half an hour past, leafmotor replied me and asked me to check the bearings. How to check hub motor bearing? Take off two bearings from axis, and use little finger to hold inside of bearing, the other hand to turn bearing, faster, better. If you can hear some noise from bearing that can confirm the problem comes from electric bike motor ‘s bearing. At last, I found there was a bearing was broken. According as the bearing model, I bought two new ones in market and replaced them.

Test electric bike kit wheel in the air, no noise. Brake hub motor wheel, still no noise. Nice, Have sloved it.

I should thank leaf motor that help me and I found fun throught repairing electric bike motor. Now I decide to buy leaf ‘s electric bike kit if I have need and will recommend my friends to order leafmotor’s electric bike motor, bike kit…

Though I haven’t ordered any goods from leafmotor by now. But they are very professional, has best service and believe they have high quality products.

Hub motor, electric bike motor, electric bike kit supplier: Leaf Motor Technology Co.,Ltd

Website:https://www.leafmotor.com

power on the electric bike hub motor was gone

Electric bike hub motor kit was gone, how to solve it?

Received my electric bike kit .Product list:

1.26” 36V 250W front brushless geared hub motor wheel

2.36V 6-MOSFET brushless motor controller working with LCD(display speed,mileage,battery gauge..)

3.standard black twist throttle with battery gauge

4.brake lever with low voltage to brake

5.three button-ON/OFF switches that are used for control front&rear lights,cruise,horn…

Check rim whether in the middle of fork and the direction of hub motor runs.Then I have installed everything on my bicycle according as instruction manual and the electric bike kit worked fine.

I was running e-bike about 25km and then I stopped the electric bike motor . Charged the electric bike battery because I was staying there for some hours. Started on the way home and after some heavy hills (about 3 km)it was completely dead. The electric bike kit system was running like normal up to this, but suddenly all power on the electric bike motor wheel was gone.

Those three led lights on twist throttle for electric bike battery were still lit. I tried to turn e-bike off and on again, but same result.

Today the electric bike kit is still dead.

Do you have any idea? Measured 0,1 Ohm between the electric bike motor(hub motor phase wire: yellow, green, blue).Infinity between hub motor cable and hub motor cover. So it does not look like it is burned. The electric bike motor controller has 41,8 Volt input.

Measure the hub motor hall sensor:

Red, black, yellow, blue, green wires.

1.The voltage between red and black is 4.5V;

2.The voltage between yellow and black is 4.2V or 0V,(When use hand to turn hub motor, the voltage will change from 0~4.5V~0~4.5V)

3.The voltage between blue and black is 0.2V; (When use hand to turn hub motor, the voltage could not change)

4.The voltage between green and black is 0.1V. (When use hand to turn hub motor, the voltage could not change)

From above test data, I doubt there were two hall sensor inside the electric bike motor that were broken.

Electric bike hub motor kit was gone, how to solve it?

Hub motor, electric bike motor, electric bike kit supplier: Leaf Motor Technology Co., Ltd

Website:https://www.leafmotor.com